Head,hands and mask - Casey Jones 2003, upper body - guitar hero, lower body - Sandman (Spiderman 3)...[See More]

Developed in solidworks for 3.75" ultron figure, this comission was based on the sideshow model. 3d printed, sanded and smoothed with acetone and painted. The zemo figure is there only for scale....[See More]

Build over a mdf piece with styrofoam as the sculpted material for the crater, sidewalk, and walls. Street texture was made using thin gravel and glue. The remaining accesories were made in...[See More]

I made this junkyard with no real direction in mind. I thought maybe GI Joe's, but they are still too big for this setup. My next thought was Walking Dead building sets minfigures would be a nice fit...[See More]

my first dio pink foam paint and some love. went with pre made plastic sheets for brick walls acrylic paint pretty much got it done in about 3 days maybe 8 hours of work time...[See More]

For this set, I used two figures: - Hannibal Lecter in Holding Cell (NECA) for the head and the shoes - Bishop (NECA) for the body I remodeled holding prisoner from Bishop's and made a more...[See More]

This is a multi purpose display I made to show figures and staging. I constructed it from Owens Corning foam board. I then draw most of the detail work in ballpoint pen. The cobblestone, brick work,...[See More]

C-3PO: I painted the whole figure with golden spray and brush up the right leg with silver paint. R2-D2: I cast the blue sides (with epoxy) and repainted the picture with brush. I made the basis of...[See More]

100% Styrofoam, 24 inch 3 variant size styrofoam ball Paper clay It stand on 24 inch size tower over my SDCC galactus and almost about the size of my custom eternity....[See More]

Vault of Armor from War Machine War Machines vault never made it to the big screen so it came directly from my imagination. Took the Hellicarrier vault for Iron Man for inspiration. Hope you guys...[See More]

. . . Hello realmpeople. this is nearly a smaller,non-lighted,but more detailed version of my first tmnt diorama. Made of cork,fimo air light,paper and cheap discount acrylcolors Thanks for...[See More]

Hi All, The dio is complete and is called RESCUE. As mentioned before it depicts a Tie fighter going down in the desert and after a few days the pilot finally is able to pick up a transmission on...[See More]

My first attempt to make a diorama for my Dragon ball z figures. built from the following materials. cardboard,hotglue,paper towel,dry stem,water and acrylic paint....[See More]

Sarah Connor: I have slightly modified the NECA figurine. NECA has done a great job by offering us three different heads but none matched this very stage ! So I added the glasses that come from...[See More]

Perform this diorama using polystyrene at the base foam to sculpt the ground and Polyfer for the rest. The columns are made of cardboard tubes filled Styrofoam sticks to give firmness and...[See More]

for the base I used 3- 2ft by 4ft foam boards(from bunnings) 30mm thick coved in watered down pva glue then sprinkled sand over the top allowwed to dry.then marked out where I wanted the water, cut...[See More]

Odin is the All-Father of the Norse gods and ruler of Asgard. He is the son of Bor, brother of Vili and Ve, husband of Frigga and the father of Thor, Vidar, Balder and adoptive father of Loki. Odin...[See More]

Hi All, Here are my usual outdoor pics, I have used an older camera for the shots so hopefully they will look good on your screens. Recipe. The Speeder - is from Bandai and built straight out of...[See More]

These are some bought dumpsters, I did a repainted of them and aged them up a bit with some rust and damage effect....[See More]

I use a font, plastic, paper, paint,cables, and more details for the door usea a nails to open and close, and make a rook with plastic for contein the lighs and cables...[See More]

The throne base was made from diff figures put all together,sculpted some parts and painted,this throne would be perfect to your deadpool figure comments are welcome...[See More]

This is a very large display I'm calling it "marvel warzone" it is fully finished inside and out for full 360 displaying and it is magnetized for easy storage...[See More]

NECA figurines are: - Dutch jungle disguise - Water emerging hunter jungle Dutch: I remodeled her hair so "wet" repositioned both arms back, re-sculpted the jacket he still has to this point in...[See More]

- The head comes from the Terminator "Ultimate" from NECA. - The torso and arms are those of Dutch version of "shirtless" of NECA. - For the pelvis and thighs: a wrestler WWE figurine. - Legs and...[See More]

Just a simple repaint. Drybrushed orange for the chair, white for the skulls, and some burnt yellow for some of the accent bones....[See More]

This is the 2nd WWE dumpster I had repainted and added some filler to the cracks. Comments and suggestions welcomed....[See More]

Hi All, I know it's not it's not a custom but I figured that I would post all my diorama's here instead of making different sections. This dio depicts a Rebel Maintenance crew getting ready to some...[See More]

Hi All, Completed this dio the a few weeks ago, I have been playing a lot of Battlefront and decided to do a bunker assault theme. Recipe Figures - the figures are from Bandai and are built...[See More]

I have been working on this one off and on for the last year, and I finally finished it. I have made a ton of mechs before, but I wanted to try my hand at making a hangar for the mech. Here is what...[See More]

Hi All, Again while playing Battlefront I was playing the Drop Zone level and thought how cool it would be to have a small dio so it it is. Figures - the figures are from Bandai and built straight...[See More]